6
System Connections
•
Do not plug in the power cord until all connections have been made.
•
On each pair of input or output jacks, the jack marked R corresponds to the right channel and the jack marked L corresponds to the left
channel.
Two types of output jacks are located on the rear panel.
Use the DIGITAL OUTPUT jack if you are connecting the unit to
audio equipment that supports a digital connection.
ANALOG OUTPUT jacks:
These are the most commonly used jacks. Connect these jacks to
the amplifier’s CD input jacks using the supplied audio connection
cable.
DIGITAL OUTPUT (optical output) jack:
For digital recording, connect this jack to the digital input jack of a
Mini Disc recorder, a DAT deck, or other digital equipment. If your
amplifier has a digital input jack, connecting the DIGITAL OUT-
PUT jack to it will produce a much clearer and more dynamic
sound.
•
Terminal protection cap is attached to the digital jack.
Remove the cap when connecting the unit to other digital equip-
ment. When you are not using the digital output jack, replace
the cap.
•
Refer to the amplifier’s instruction manual for connections.
When connecting Onkyo/Integra products, it is necessary to attach
the cable to be able to use the remote controller of the main
component to control the entire system.
1. To use this CD changer with an amplifier (or receiver), cassette
tape deck, and tuner that include the appropriate jack, con-
nect the components using the cable, plugged into the
REMOTE CONTROL jacks.
2. As the exact connection sequence of the cable is unimpor-
tant, you can connect from the amplifier (or receiver) to either the
tuner, cassette tape deck, or compact disc changer.
3. To operate correctly, the remote controller must point toward the
remote control sensor of the amplifier (or receiver).
Notes:
•
The upper and lower REMOTE CONTROL jacks have the
same function.
•
Remote controller operation is not possible when only the
cable is connected – the audio connection cables must also be
connected.
•
An cable equipped with a 3.5mm (1/8 in.) diameter minia-
ture two-conductor phone plug is included with this unit and
with every tuner and cassette tape deck that utilizes the
jack.
Before plugging in the unit, confirm that all connections have been
made properly.
1.
Insert the AC power supply cord into the outlet.
2.
Press the POWER button.
•
When the power first turns on, the carousel rotates to find a disc
and stops automatically if there is a disc on the disc tray.
Audio
connection cable
CD
LR
Optical IN
cable
Amplifier
DAT, MD recorder or
Digital amplifier
Optical fiber cable
(not included)
AC INLET
OPTICAL
ANALOG
OUTPUT
DIGITAL
OUTPUT
COMPACT DISC CHANGER
MODEL NO.
CDC-3
2-1, NISSHIN-CHO, NEYAGAWA- SHI, OSAKA,
JAPAN MANUFACTURED IN MALAYSIA
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
AVIS
REMOTE
CONTROL
L
R
RATING:
AC120V 60Hz 10W
To wall
outlet
Connecting a power cable
1. Connect the outlet plug on the included power
cable to the AC INLET on the CDC-3.
2. Plug-in the other end of the cable to a wall AC
outlet.
Note:
• Do not use any power cable other than the included
cable. The included cable is designed for use only
with the CDC-3. Do not use it for any other device.
• Do not connect or disconnect the outlet plug from
the CDC-3 while the other end is plugged into the
wall AC outlet.
Connecting to an audio system
Connections for remote controller ( )
Connecting the power
To AC
outlet
POWER
OFFON
12
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals